Loading the model…
Drag to rotate, scroll or pinch to zoom, right-drag to pan. All measurements are in millimetres.
Dimensioned drawings
Projected from the same 3D model, so they always match it. Select a drawing to open it full size.
Shopping list: one order from Mouser
Every part was in stock at Mouser on 20 November 2026. Mouser was the only store checked that had the header-less Pico 2 W; Adafruit, Digi-Key and Amazon were all out of it. The case is sized to these exact parts.
| Part | Qty | Mouser part no. | Cost | In stock |
|---|---|---|---|---|
| Raspberry Pi Pico 2 W SC1633, no headers | 1 | 358-SC1633 | $7.00 | 1,778 |
| Key switches, 10-pack Kailh linear red (Adafruit 4952). Clicky white 485-4955 and tactile brown 485-4954 cost the same | 1 | 485-4952 | $6.95 | 8 packs |
| Keycaps, 10-pack Relegendable 1u caps with clear label covers (Adafruit 5039) | 1 | 485-5039 | $4.95 | 38 packs |
| Rotary encoder with push switch Bourns PEC11R-4220F-S0024: M7 bushing, 6 mm D shaft, 20 mm; nut and washer included | 2 | 652-PEC11R-4220F-S24 | $4.68 | 8,103 |
| Encoder knob Slim 11.5 mm D-shaft knob (Adafruit 5093) | 2 | 485-5093 | $1.50 | 277 |
| M3 brass heat-set insert SI IUTB-M3, straight wall, 4.55 × 5.74 mm | 4 | IUTB-M3 | $1.60 | 51,505 |
| M3 × 6 steel pan-head screw Keystone 29311, slotted, zinc plated | 4 | 534-29311 | $1.88 | 4,049 |
| Rubber feet, 4-pack About 8 mm × 4 mm stick-on bumpers (Adafruit 550) | 1 | 485-550 | $0.95 | 26 packs |
| Hookup wire, 2 m, black 30 AWG silicone stranded (Adafruit 2003) | 1 | 485-2003 | $0.75 | 213 |
| Hookup wire, 2 m, green 30 AWG silicone stranded (Adafruit 2005) | 1 | 485-2005 | $0.75 | 62 |
| Parts total Before shipping, sales tax and any import tariff Mouser adds in the cart | $31.01 | |||
| USB-A to micro-B data cable, 1 m Same Sky CBL-UA-MUB-1. Skip it if you already have one | 1 | CBL-UA-MUB-1 | $4.10 | 2,044 |
- No diodes are needed: each of the nine keys and both encoders wires straight to its own Pico pin.
- You also need filament and a soldering iron with solder. The iron presses in the four inserts too.
- The Pico needs no screws. It drops onto four printed pegs and the top shell holds it down.
- Mouser's pages flag a possible tariff on the Pico (8%) and the encoders (21%); the amount shows in the cart.
Key numbers
| Outside size | × × mm |
|---|---|
| Height to keycap tops | mm from the desk |
| Height to knob tops | mm from the desk |
| Switch cutouts | 9 × mm square, mm clip lip, mm pitch |
| Encoder holes | 2 × Ø mm, mm apart, mm right of the last key column |
| USB opening | × mm, centred on the rear wall, centre mm up |
| Walls / deck / base | / / mm |
| Rubber feet | 4 recesses, Ø × mm deep |
| Legs | × × mm, swing ° to a hard stop |
| Tilt with legs open | °; rear edge sits mm above the desk ( mm when flat) |
| Room under the switches | mm between the Pico and the switch pins |
Printing
- Top shell: upside down, deck on the bed. No supports.
- Bottom plate: desk side down. The leg pockets bridge about 20 mm; add support there if your printer sags.
- Legs (print 2): flat. They snap in from below and stay put by friction.
- PETG is the safer choice for the bottom plate, because the leg sockets flex when the legs snap in.
Check before printing
- The model is checked in software only: every part is a valid solid and nothing collides. It has not been printed.
- The encoder pocket is cut for the Bourns PEC11R body (12.5 × 13.4 mm). A different encoder may not fit.
- Measure your USB cable's moulded plug. It has to pass through the 13 × 8 mm opening.
- The knob's fit on the Bourns D shaft is taken from Adafruit's listing, not measured.
- The Pico's BOOTSEL button can't be reached once the case is closed. Flash it first, or use firmware that can reboot into the bootloader.